masonry | landscape | pipe | precast | prestressed | ready-mix

Technical Service Bulletins

Service bulletins by category:
Bins and Batching
 Block Machines
 Block Machine Changeover Procedures
Splitters/Turnovers
Cubers
Electrical
 Frequency Drives
Hydraulic
Mixers
Molds
Multi-Spade Besser-Matic
Rack Transporters
Skip Loaders
Safety

Service bulletins by date

Technical Service Contact Information
 Phone 800.968.0444 or 989.354.4111 (option 4 for technical service).

E-mail me new technical service information
Some of the information below requires Adobe Acrobat, and is indicated with this icon.  Download Now!


Bins and Batching

Bulletin Number
HTML format

Description

Printer-friendly format (PDF)
06-9 Conveyor Belt Basic Rules and Procedures for
Tracking and Training 
06-16 Conveyor Belt Squaring and Cutting Procedure
06-17 Conveyor Belt Installation and Splicing Procedure
06-18 Conveyor Belt Troubleshooting Guide
06-19 Conveyor Belt Storage
02-6 Checking Sheave Alignment on Equipment that is V-Belt Driven
01-8 Recommended Cement Content of Concrete Masonry Units
01-4 Screw Conveyor Operation and Maintenance
01-3 Dust Collector Maintenance and Troubleshooting

Back to Top

Block Machines

Bulletin Number
HTML format

Description

Printer-friendly format (PDF)
07-7 Proper Procedure for Using Air Compaction on Block Machines
07-6 Indexing a New Style Bull Gear
06-25 Replacing a Broken Pallet Timing Bolt on a V3-12
06-24 Replacing a Broken Pallet Timing Bolt on a Dynapac, Ultrapac, V5 or Superpac
06-23 Smartpac® Air/Hydraulic System Diagrams
06-14 Operation of the Automatic Feed Time Adjust
06-13 Adjustments and Operation of the Automatic Feed Control
06-12 AFC Smartpac Operating Instructions
06-11 The Importance of Synchronizing Vibration
06-8 Allen-Bradley Panelview Self Test Numbers
06-6 Ultrapac Anvil Configuration

03-3

Proper Tensioning of Drive Belts on a Block Machine

02-6 Checking Sheave Alignment on Equipment that is V-Belt Driven

02-1

Pallet Lug Link Pins

01-9

Changing the Bull Gear and Pinion Shaft on a Dynapac, Ultrapac, V5 or Superpac
01-2

Bull Gear and Pinion Indexing and Replacement Recommendations
00-8 Adjustment of the Pallet Moving Arm Springs on a V3-12
00-7 Replacing the Main Shaft Bearings on a Block Machine
00-1 Installation of KAMCO box (to replace GEMCO box)
99-3 Bolt Torque Specifications
97-5 Recommendations for use of Vibrator weights
97-4 Updated adjustments for 5-5/8" high units on a V-4 or V-4 (26"deep machine) 
97-1 Using the Encoder for Allen-Bradley SLC™-500 programmable logic controllers 
96-5 V3-12 Pinion shaft assembly (Besser No. 464229) installation w/locking assembly 
95-7 New style crossport and singling plate 
95-5 Using the Encoder for Allen-Bradley PLC®-2Progammable logic controller 
95-4 Instruction to move electrical box to left hand side of vibrator motor 
95-3 Modify Air Compaction Device air cylinders to reduce rod wear 
95-2 Gemco cam limit switch boxes (Supercedes SB-No. 90-6) 
95-1 Check the Bescodyne Clutch/Brake stacks for wear 
94-3 Update Bescodyne Clutch/Brake units from single to double air flow valve 
94-2 Extending life of Bescodyne units 
93-5 Agitator encoder set-points 
93-4 The Bescodyne drive service tip 
92-2 Adjusting second stop on Besser cam operated machines 
91-2 How the Trabon Air Grease Pump Works 
91-1 Improved pneumatic control system for Bescodyne vibrators 
89-3 Vibrator motor sheaves for block machines 

Back to Top

 

Block Machine Changeover Procedures

 

Changeover Procedure Terminology

Bulletin Number
HTML format

Description

Printer-friendly format (PDF)
06-20 Terminology for Block Machine Changeover
       Procedures

 

Dynapac, Ultrapac and Superpac Procedures
using Quick Change Pallet Receiver Cams

Bulletin Number
HTML format

Description

Printer-friendly format (PDF)
06-21 From 7 5/8" high units to 3 5/8" high units
06-22 From 7 5/8" high units to 5 5/8" high units

Back to Top

 

Cubers

Bulletin Number
HTML format

Description

Printer-friendly format (PDF)
03-1 Cuber Limit and Proximity Switch, and Photo Eye Setup Guide (PDF Only)
89-6 SF and AF Cuber Wire mesh belt installation and adjustment instructions
89-5 SF-7 and SF-7W Cuber slider plate drive sprocket and wear bar adjustments
89-2 Quick reference guide for ordering AF-7 wear plates

Back to Top

 

Splitters and Turnovers

Bulletin Number
HTML format

Description

Printer-friendly format (PDF)
03-2 Splitter with Turnover Limit and Proximity Switch, and Photo Eye Setup Guide (PDF Only)
01-6 Splitter Blade Wear and Adjustment
01-5 Splitting 8 Inch Return Corners
00-2 Troubleshooting the S63 EZ Splitter Setup

Back to Top

 

Electrical

Bulletin Number
HTML format

Description

 Printer-friendly format (PDF)
06-15 Troubleshooting The Digisolver for Allen Bradley SLC-500
06-5 Procedure for Programming Allen Bradley 1336 Impact Frequency Drives
when used with AFC Smartpac Vibration
06-4 New VersaView out of box set up s
06-2 Set Up IP Address for 6182H - VersaView CD1250H s
06-1 Load Existing VersaView Screen with New Program s
02-4

SLC -500 Error Codes
02-3

Bescodyne Solenoid Valve Supplier
00-5 Locked and Open Rotor Test for a 10 HP Vibrator Motor  
00-1 Installation of KAMCO box (to replace GEMCO box)
99-2 Installing Screen Program in PanelView™ 900/1000 with a Flash Card
98-1 Xycom 2050 Graphics Display Unit set-up information for use with a PLC®
97-3 SLC™-500 programmable controller
95-2 Gemco cam limit switch boxes (Supercedes SB-No. 90-6)
94-1 Xycom 2050 Graphics display unit set-up information
93-2 Besser NEMA and current transformer type
92-1 Putting Allen-Bradley SLC™-150 controllers back in the RUN MODE
90-4 T-30 plant floor terminal set-up information

Back to Top

 

Frequency Drives

 

Block Machines

Agitator

Bulletin Number
HTML format

Description

Printer-friendly format (PDF)
07-8 Procedure for Programming the 5HP PowerFlex 70 Agitator Frequency Drive

Back to Top

Block Moving Bars

Bulletin Number
HTML format

Description

Printer-friendly format (PDF)
07-10 Procedure for Programming the 5HP PowerFlex 70 and 700 Block Moving Frequency Drive used with Clutch and Brake
07-9 Procedure for Programming the 5HP PowerFlex 70 and 700 Block Moving Frequency Drive used with Warner Brake

Back to Top

Main Drive

Bulletin Number
HTML format

Description

Printer-friendly format (PDF)
07-15 Procedure for Programming the Main Drive 75 HP PowerFlex 700 Frequency Drive
07-12 Procedure for Programming the Main Drive 1336E Impact Frequency Drive
07-11 Procedure for Programming the Main Drive 1336 Impact Frequency Drive

Back to Top

SmartPac®

Bulletin Number
HTML format

Description

Printer-friendly format (PDF)
07-19 Procedure for Programming the SmartPac 10HP PowerFlex 700 Vibrator Frequency Drive
07-18 Procedure for Programming the 15HP PowerFlex 700 Vibrator Frequency Drive used with Dual Vibration

Back to Top

 

Hydraulic

Bulletin Number
HTML format

Description

Printer-friendly format (PDF)
97-2 Achieving peak hydraulic system efficiency
90-5 Hydraulic tank liquid level switches

Back to Top

 

 

Mixers

Bulletin Number
HTML format

Description

Printer-friendly format (PDF)
07-04 Enhanced Mixer (EM) Discharge Gate Seal
03-5 Proper Tensioning of Drive Belts on Batch and Slump Mixers
02-2 New Mixer Blade Sets of Parts and Installation Procedure Using Epoxy
99-1 Breather Vent and Split Oil Seal
89-1 6, 9 and 10 yard slump mixer air/grease purged dust hubs

Back to Top

 

 

Molds

Bulletin Number
HTML format

Description

Printer-friendly format (PDF)
02-5 Improved Low Height End Liners with 1" Keys
01-7 Stripper Shoe Set-Up Gauge
01-1

High Strength Vibrator Bolts - Revised 9 August 2005
00-6 Concrete Industry Definitions for Mold Parts
97-6 Portable Mold Jig
97-5 Recommendations for use of Vibrator weights
96-4 Besser Mold assembly and torque requirements
96-3 Descriptions and examples of how to order mold parts
96-2 Mold compartment dimensions
93-1 Quick order reference quide for mold pallet guides 
(Supercedes SB-No. 90-2)
90-3 Quick reference guide for ordering agitator grids
90-2 Mounting Posapac Vibrator Shaft Assemblies to a Mold

Back to Top

 

 

Multi-Spade Besser-Matic

Bulletin Number
HTML format

Description

Printer-friendly format (PDF)
07-5 Proper Mounting of Bescoshear Brakes s
06-3 Dodge Quantis Oil Level Recommendations s
05-1 How to Time a Geneva Drive
03-4 Proper Tensioning of Drive Belts on a Besser-Matic
02-6 Checking Sheave Alignment on Equipment that is V-Belt Driven
00-4 Procedure to Align Carriage and Ball Screw

00-3

 Besser-Matic® 1305 Frequency Drive Programming Instructions

93-3

 Dip switch adjustments - Warner CBC-300 adjustable brake control

Back to Top

 

 

Rack Transporters

Bulletin Number
HTML format

Description

Printer-friendly format (PDF)
99-4 Limit and Proximity Switch Location and Part Numbers on a LSC-40C Car and Crawler
91-3 LSC-40 rotating cable anchor

Back to Top

 

 

Skip Loaders

Bulletin Number
HTML format

Description

Printer-friendly format (PDF)
89-4 Boston gear 700 series reducer lubrication

Back to Top

Besser Company,  801 Johnson Street, Alpena,  MI  49707 USA , 989.354.4111 | email:  sales@besser.com | Employee Login