Technical Service Bulletins

If you have additional service questions, please call us at 800.968.0444 or 989.354.4111.
If you have general technical service questions, not of an urgent matter, you can e-mail techservice@besser.com.

Service bulletins by category

Bulletin Number HTML format	Description	Printer-friendly format (PDF)
07-19	Procedure for Programming the SmartPac 10HP PowerFlex 700 Vibrator Frequency Drive
07-18	Procedure for Programming the 15HP PowerFlex 700 Vibrator Frequency Drive used with Dual Vibration
07-15	Procedure for Programming the Main Drive 75 HP PowerFlex 700 Frequency Drive
07-12	Procedure for Programming the Main Drive 1336E Impact Frequency Drive
07-11	Procedure for Programming the Main Drive 1336 Impact Frequency Drive
07-10	Procedure for Programming the 5HP PowerFlex 70 and 700 Block Moving Frequency Drive used with Clutch and Brake
07-9	Procedure for Programming the 5HP PowerFlex 70 and 700 Block Moving Frequency Drive used with Warner Brake
07-8	Procedure for Programming the 5HP PowerFlex 70 Agitator Frequency Drive
07-7	Proper Procedure for Using Air Compaction on Block Machines
07-6	Indexing a New Style Bull Gear
07-05	Proper Mounting of Bescoshear Brakes
07-04	Enhanced Mixer (EM) Discharge Gate Seal
06-25	Replacing a Broken Pallet Timing Bolt on a V3-12
06-24	Replacing a Broken Pallet Timing Bolt on a Dynapac, Ultrapac, V5 or Superpac
06-23	Smartpac® Air/Hydraulic System Diagrams
06-22	From 7 5/8" high units to 5 5/8" high units
06-21	From 7 5/8" high units to 3 5/8" high units
06-20	Terminology for Block Machine Changeover Procedures
06-19	Conveyor Belt Storage
06-18	Conveyor Belt Troubleshooting Guide
06-17	Conveyor Belt Installation and Splicing Procedure
06-16	Conveyor Belt Squaring and Cutting Procedure
06-15	Troubleshooting The Digisolver for Allen Bradley SLC-500
06-14	Operation of the Automatic Feed Time Adjust
06-13	Adjustments and Operation of the Automatic Feed Control
06-12	AFC Smartpac Operating Instructions
06-11	The Importance of Synchronizing Vibration
06-9	Conveyor Belt Basic Rules and Procedures for Tracking and Training
06-8	Allen-Bradley Panelview Self Test Numbers
06-6	Ultrapac Anvil Configuration
06-5	Procedure for Programming Allen Bradley 1336 Impact Frequency Drives when used with AFC Smartpac Vibration
06-4	New VersaView Out of Box Set Up
06-3	Dodge Quantis Oil Level Recommendations
06-2	Set Up IP Address for 6182H - VersaView CD1250H
06-1	Load Existing VersaView Screen with New Program
05-1	How to Time a Geneva Drive
03-5	Proper Tensioning of Drive Belts on Batch and Slump Mixers
03-4	Proper Tensioning of Drive Belts on a Besser-Matic
03-3	Proper Tensioning of Drive Belts on a Block Machine
03-2	Splitter with Turnover Limit and Proximity Switch, and Photo Eye Setup Guide (PDF Only)
03-1	Cuber Limit and Proximity Switch, and Photo Eye Setup Guide (PDF Only)
02-6	Checking Sheave Alignment on Equipment that is V-Belt Driven
02-5	Improved Low Height End Liners with 1" Keys
02-4	SLC -500 Error Codes
02-3	Bescodyne Solenoid Valve Supplier
02-2	New Mixer Blade Sets of Parts and Installation Procedure Using Epoxy
02-1	Pallet Lug Link Pins
01-9	Changing the Bull Gear and Pinion Shaft on a Dynapac, Ultrapac, V5 or Superpac
01-8	Recommended Cement Content of Concrete Masonry Units
01-7	Stripper Shoe Set-Up Gauge
01-6	Splitter Blade Wear and Adjustment
01-5	Splitting 8 Inch Return Corners
01-4	Screw Conveyor Operation and Maintenance
01-3	Dust Collector Maintenance and Troubleshooting
01-2	Bull Gear and Pinion Indexing and Replacement Recommendations
01-1	High Strength Vibrator Bolts - Revised 9 August 2005
00-8	Adjustment of the Pallet Moving Arm Springs on a V3-12
00-7	Replacing the Main Shaft Bearings on a Block Machine
00-6	Concrete Industry Definitions for Mold Parts
00-5	Locked and Open Rotor Test for a 10 HP Vibrator Motor
00-4	Procedure to Align Carriage and Ball Screw
00-3	Besser-Matic® 1305 Frequency Drive Programming Instructions
00-2	Troubleshooting the S63 EZ Splitter Setup
00-1	Installation of KAMCO box (to replace GEMCO box)
99-4	Limit and Proximity Switch Location and Part Numbers on a LSC-40C Car and Crawler
99-3	Bolt Torque Specifications
99-2	Installing Screen Program in PanelView™ 900/1000 with a Flash Card
99-1	Breather Vent and Split Oil Seal
98-1	Xycom 2050 Graphics Display Unit set-up information for use with a PLC®
97-6	Portable Mold Jig
97-5	Recommendations for use of Vibrator weights
97-4	Updated adjustments for 5-5/8" high units on a V-4 or V-4 (26"deep machine)
97-3	SLC™-500 programmable controller
97-2	Achieving peak hydraulic system efficiency
97-1	Using the Encoder for Allen-Bradley SLC™-500 programmable logic controllers
96-5	V3-12 Pinion shaft assembly (Besser No. 464229) installation w/locking assembly
96-4	Besser Mold assembly and torque requirements
96-3	Descriptions and examples of how to order mold parts
96-2	Mold compartment dimensions
95-7	New style crossport and singling plate
95-5	Using the Encoder for Allen-Bradley PLC®-2Progammable logic controller
95-4	Instruction to move electrical box to left hand side of vibrator motor
95-3	Modify Air Compaction Device air cylinders to reduce rod wear
95-2	Gemco cam limit switch boxes (Supercedes SB-No. 90-6)
95-1	Check the Bescodyne Clutch/Brake stacks for wear
94-3	Update Bescodyne Clutch/Brake units from single to double air flow valve
94-2	Extending life of Bescodyne units
94-1	Xycom 2050 Graphics display unit set-up information
93-5	Agitator encoder set-points
93-4	The Bescodyne drive service tip
93-3	Dip switch adjustments - Warner CBC-300 adjustable brake control
93-2	Besser NEMA and current transformer type
93-1	Quick order reference quide for mold pallet guides (Supercedes SB-No. 90-2)
92-2	Adjusting second stop on Besser cam operated machines
92-1	Putting Allen-Bradley SLC™-150 controllers back in the RUN MODE
91-3	LSC-40 rotating cable anchor
91-2	How the Trabon Air Grease Pump Works
91-1	Improved pneumatic control system for Bescodyne vibrators
90-5	Hydraulic tank liquid level switches
90-4	T-30 plant floor terminal set-up information
90-3	Quick reference guide for ordering agitator grids
90-2	Mounting Posapac Vibrator Shaft Assemblies to a Mold
89-6	SF and AF Cuber Wire mesh belt installation and adjustment instructions
89-5	SF-7 and SF-7W Cuber slider plate drive sprocket and wear bar adjustments
89-4	Boston gear 700 series reducer lubrication
89-3	Vibrator motor sheaves for block machines
89-2	Quick reference guide for ordering AF-7 wear plates
89-1	6, 9 and 10 yard slump mixer air/grease purged dust hubs